How to clean iron from burnt cloth

Every housewife once encountered the problem of burnt fabric on the sole of the iron. This phenomenon occurs when the temperature is not observed during ironing. The result in the end is one - a spoiled thing and a black coating on the iron. This raises the question of how to clean the surface. Consider the most effective methods for removing carbon deposits on the bottom of the thermal device.

Method number 1. Special pencil

1. Plug the iron into a power outlet, set the power to a medium level. Wait for the sole to heat up. Then remove the cleaning pencil from the packaging and rub the surface of the thermal device.
2. The process does not take long, the composition of the cleaning agent will begin to drain with the remnants of burning. Remove any remaining dirt with a paper towel.
3. Stick to safety precautions. Be careful, the molten composition should not get on the skin, otherwise burns can not be avoided.
4. Also, when applying a pencil on a hot plane, a pungent odor will be emitted. The cleaning product is suitable for removing soot from all types of soles.

Method number 2. Salt

1. The method is considered one of the most budgetary and effective. Removing the darkening on the sole of the iron can be done in two ways. Be careful, the method cannot be used on Teflon-coated irons.
2. In the first case, distribute 120 g. fine salt on a parchment sheet of paper. Heat the iron to maximum temperature, move the appliance forward as you would iron your clothes.
3. In the second case, pour 150 g. table salt in a thin cotton cloth. Preheat the appliance to the maximum, remove dirt from the bag with loose composition.

Method number 3. Paraffin candle

1. A paraffin candle will help to cope with plaque and a small deposit. Wrap the product in a cotton cloth, heat the iron to maximum temperature.
2. Run the candle on the hot sole of the thermal device. Liquid paraffin will remove most of the contaminants.
3. After that, clean the holes on the sole, if any, with steam. Such a move will help to avoid the appearance of greasy spots during the next ironing of things.
4. When carrying out an iron cleaning operation, pre-lay a paper towel so that hot soot drips onto it. At the end of the procedure, wipe the sole of the thermal device with a napkin.

Method number 4. Table vinegar

1. Vinegar is able to rid the iron of fresh soot. To remove light dirt, soak a cotton handkerchief in a 9% solution, wipe the slightly warm sole of the iron.
2. A longer cleansing method is also possible. Moisten a cotton towel in vinegar, place a device that is not connected to the mains on it. Wait a day, after the expiration of the period, remove the remnants of soot with a paper towel.

Method number 5. Lemon acid

1. For such manipulations, a solution based on citric acid is suitable as a cleaning agent.
2. Dilute 80 g in 300 ml of warm water. loose composition. Repeat the procedure in the same way as with vinegar.

Method number 6. Hydrogen peroxide and ammonia

1. Dilute in a small container of 30 ml. hydrogen peroxide and 10 ml. ammonia. Saturate with a cotton towel.
2. Remove soot on the warm sole of the iron with an impregnated cloth. Be prepared for the pungent smell of ammonia.

Method number 7.Hydroperite and Soda

1. When using soda to remove various contaminants, remember that the product is an abrasive substance and can scratch an unprotected surface.
2. Make a mixture of soda and water, reminiscent of gruel. Put the composition on the dirty surface of the iron, rub the surface with a cotton towel. Remove the rest with a napkin.
3. Manipulation with hydroperit should be carried out in a ventilated room, such a tool has a pungent odor. Heat the sole of the iron, apply the product in the form of tablets in the area of ​​dirt, in the case of a cleaning pencil. Wipe up the rest with a paper towel.

How to clean teflon coating

To remove carbon deposits from the Teflon surface, it is worth resorting to special sponges or pencils. Before using one of the tools, read the instructions in detail.

1. Vinegar and essence. It is also possible to cleanse with vinegar. Follow precautions, protect the skin with silicone gloves, this move will help to avoid unwanted burns. If we talk about vinegar essence, moisten the fabric in it, iron the material with a hot iron. The ongoing manipulation should be enough. Always observe the temperature when ironing things.
2. Solvent. To remove tissue deposits on the sole of the iron, you can resort to an ordinary paint solvent. Moisten a cotton pad with chemical composition, clean the place of contamination with it.
3. Foil. The method using foil is no less effective than all the others. Take a thick sheet of foil, spread on a flat board. Set the iron to maximum power, wait until the thermal device is fully heated. Now smooth out the aluminum blade as if you were ironing a simple thing. Remove any remaining dirt with a tissue.
4. Powder for brushing teeth. The tool is quite common in everyday life, but few people brush their teeth. Moisten a cotton swab with water, apply powder on it. Then wipe the warm sole of the iron in places of contamination. This method cannot be applied to ceramic surfaces.
5. Toothpaste and soda. The use of household products will help get rid of old dirt on a metal coating. Mix soda or whitening toothpaste with a little water. Apply contamination and rub thoroughly with a sponge. Do not forget, both tools have an abrasive structure, they do not fit all types of soles of irons.
6. Laundry soap. To clean the sole of adhering synthetics, heat the surface of the iron to the maximum mark. Rub with soap, then remove the dirt with a paper towel. After that, rub the sole again with household soap and wipe with a damp cloth. The applied method is suitable for fresh contaminants.

How to clean ceramic coating

1. If you encounter the problem of a burnt piece of cloth, a kitchen wooden spatula will help to rectify the situation. Heat the iron at maximum power, then use a household appliance to gently remove contamination.
2. Then mix in a small container 10 ml. 9% table vinegar and 30 ml. warm water. Dampen a cotton towel, wipe the sole of the iron.
3. You can also put a hot iron on the fabric-soaked fabric for a few seconds. Or resort to the help of a nylon washcloth by wiping the hot surface of the thermal device with it, you can achieve the desired result.

Simple and affordable iron cleaning tools

1. Wet a small piece of cloth with hydrogen peroxide, then wipe the area with the formed plaque. Perform the procedure on a warm surface.
2. Acetone is also a good and effective tool, repeat the manipulations described when using hydrogen peroxide.
3. Dampen a flannel rag with lemon juice and a few drops of ammonia.Then walk with a wet cloth to the area of ​​contamination.

Practical tips for cleaning the iron

1. When buying an iron, carefully read the operating instructions. Perhaps it will indicate how to clean the soles.
2. Before ironing, always pay attention to the fact whether a thing can be ironed and at what temperature.
3. After using the thermal device, always wipe the sole of the iron with a damp cloth, and clean it from scale inside.
4. If it comes to thoroughly cleaning the soleplate, pay attention to the coating. Carefully carry out all manipulations without scratching the surface.

It is easy to clean the sole of the iron at home if you follow practical recommendations and effective methods. The main thing is to choose the appropriate method based on the type of coating. In the future, observe the temperature regime when ironing things.

Video: how to clean a burnt iron