How to clean an iron from a burnout at home

There are many options for irons for every taste. Manufacturers offer devices with different types of coatings: Teflon, ceramics, aluminum and others. But they have one problem. With overexposure of the heated sole to the fabric, there is a chance of a burn, which is difficult to eliminate with ignorance and lack of experience. If the scum inside is removed with vinegar, but the burnt fabric will not easily lag behind. Let's look at effective ways to deal with the problem.

Methods for cleaning the iron from the burn

Experienced housewives recommend not to hesitate and immediately start cleaning. Let's look at the basic principles and the means that are suitable for these purposes.

Table vinegar

1. To prepare the composition, it is necessary to use vinegar with a concentration of 9%. Mix 160 ml. purified (!) water with 40 ml. composition. Dip a cotton or linen napkin into the solution, it is these fabrics that withstand high temperatures.
2. Turn on the iron and set the power to the middle mark. Preheat the appliance, and then begin to wipe the warm sole with a napkin folded into several layers. The burn will gradually recede, therefore difficulties should not arise.
3. If necessary, perform manipulations several times. Rinse the remaining dirt in vinegar. To clean the steam vents, use cotton swabs and the vinegar formula above.
4. Care should be taken when handling the hot sole of the iron. Also, in the process of heating, vinegar smells not very nice, so we advise you to open the windows.

Paraffin

1. If you have a candle made of paraffin, then grate it on a fine-grained grater and combine with extra-class salt (fine). Larger crystals will damage the sole, so salt should not be used.
2. You can use pure paraffin without salt. To do this, put the iron in an upright position, place a tray under it, turn on the appliance and rub the candle into the sole.

Toothpaste

1. To use the composition for domestic purposes, you can purchase even the cheapest toothpaste without granules. Powder for brushing your teeth, diluted with water to a porridge condition, is also suitable.
2. Use is straightforward. Apply the composition on a cold surface where there is carbon deposits. Rub with a cotton or linen cloth until the marks disappear.
3. Leave the product to act for 15-20 minutes, remove the residues. If carbon deposits are not completely removed, repeat the manipulation immediately after the first cleaning.
4. At the end of the procedure, moisten the cloth in clean water, wipe the sole of the household appliance and let it dry. Interestingly, toothpaste or powder completely removes dirt.

Peroxide

1. Use hydrogen peroxide to clean the appliance from burning. Also suitable is an analog - hydroperite in tablets.
2. The principle of the procedure is not difficult. Heat the appliance, soak a linen towel in hydrogen peroxide, and fold it in 5 layers. Wipe the hot surface until dirt is removed.
3. The hydroperite tablet must be mixed with water, after which, by analogy, wipe the sole of the iron. After all the manipulations, iron the cotton cloth to remove any residue.

Matchbox

1. To remove the burn from the surface of the iron, you must use the sulfur strip that is on the side of the matchbox. The main thing is to take sulfur from an unused box of matches.
2. Heat the iron to a medium mark. Take an empty box, begin to drive them to the place of pollution, rubbing slightly.When the entire burnout has gone, let the appliance cool down and remove the residue with a dry rag.

Ammonia

1. Ammonium chloride is an effective and inexpensive tool for cleaning the surface of burns. To use it, select any of the recipes below.
2. You can mix vinegar with a concentration of 9% with ammonia. A mixture of 50 ml is also suitable. lemon juice and 4 drops of ammonia. Some use pure ammonia in its pure form, as you like.
3. The processing principle is the same: soak a shred of flax in any of the means, heat the iron and rub it intensively with a wet rag. Then turn off the appliance, wait 7 hours, in the morning remove the residues with a simple ironing.

Salt

1. Salt is not only added to the original taste of dishes, but also used for domestic purposes. This method is not suitable when cleaning an iron with Teflon soles.
2. Spread a few blank sheets of paper, sprinkle with fine extra-class salt. Heat the iron to the maximum mark, iron the salt for a while.

Special pencil

1. On the shelves of shops there are many household means of directional action. The pencil is also called chalk for cleaning various coatings of the iron. The most popular firms for the production of products: Cinderella, Diaz, Typhoon.
2. Each chalk is accompanied by an instruction in which it is indicated on which coatings it can be applied. But the general principle of use is still there, consider it.
3. Heat the iron, then unplug it. Do not put pressure on the pencil, start rubbing the sole with a burner. When the pollution has disappeared, walk on the iron with a dry cotton or linen cloth.

Soda

1. The effectiveness of soda in domestic problems has long been known. The composition will help get rid of even old pollution. It is important to use soda wisely so as not to harm the household appliance.
2. Combine in a cup 50 gr. soda and 300 ml. warm water. Stir until the particles are completely dissolved. Distribute the product at the site of contamination with a foam sponge. Lightly rub the surface.
3. Do not forget that soda belongs to abrasive compounds. Therefore, it is forbidden to use it for Teflon-coated irons. Also, for such devices it is not recommended to resort to the help of coarse salt.
4. After you have treated the surface, the remaining soda should be removed with a clean cloth. Dry the sole of the iron with cotton towels.

Alternative remedies

1. Preheat the iron in the usual way. Rub the sole of the appliance with household soap. Wait for the surface to cool completely. Wipe with a damp cloth. A similar method is effective in fresh pollution.
2. You can do otherwise. Wipe the cold sole of the iron with a nail polish remover or paint thinner. For convenience, use a cotton pad.
3. If the soleplate is made of ceramic or similar expensive material, you can resort to using a glass cleaner. Spread it, wait a few minutes and wipe it with a microfiber cloth.

Teflon coating cleaning

Do not use abrasive products to clean the Teflon coating. In this case, there are more gentle and no less effective means that you can prepare yourself.

1. The glass cleaner does a good job of this.
2. Moisten a cotton cloth in a vinegar solution and iron the cloth. For efficiency, you can mix a little ammonia.
3. Budget options include dishwashing gel detergent.
4. Many housewives recommend using baby cream. The composition effectively copes with pollution. It is enough to wipe the hot sole with rags and cream.
5. Teflon coating can be cleaned in a not quite traditional way. To do this, you need ordinary chalk. Heat the iron and rub the sole with chalk powder. Roll up the dirt in any convenient way.You can also do with laundry soap.

Ceramic coating cleaning

1. Modern ceramic-coated irons damage clothes and leave a burnout, and it’s easy to clean appliances. To return the sole to its original appearance and former functionality, you can resort to some actions.
2. Get a simple cleaner for glass and ceramic surfaces. The composition can be bought at any household store. In most cases, the hostesses already have such products at home.
3. Spread on the cold sole of the iron; after 5 minutes, wipe the appliance with a clean sponge. If you want to act in a different way, then this will require hydroperit. Rub the hot sole of the iron with a tablet, and then remove the residue with a damp sponge.
4. Toothpaste can help with this problem. Apply the composition locally to the stain and rub it with an old toothbrush. Remove any carbon deposits with a damp cloth.
5. Often there is a situation where you can simply forget about the neat ironing of synthetic things. Then the molten material can be wiped off with a nail polish remover. From now on, spread gauze to prevent such situations.

Practical recommendations

1. Remember that delicate fabrics need to be ironed through cheesecloth, then molten particles will not remain on the sole.
2. Always clean the steam outlet if you cannot smooth creases and creases on things.
3. After using the iron, wipe the sole with a solution based on vinegar.
4. In case of emergency, use harsh cleaning agents. Otherwise, the soleplate will irreparably deteriorate.

It is easy to clean the sole of the iron yourself, if you have some knowledge. Consider common solutions to problems, and try to prevent this from happening again. Iron delicate things through wet gauze.

Video: how to clean a burnt iron