How to seal rubber boots at home

Rubber boots - shoes that are necessary not only for giving, but also for the city. They protect from the weather and dirt. But it has one drawback - any nail or a piece of glass is enough to make the shoes unusable. It’s impossible to give such boots to the workshop, but it’s a pity to throw out. Therefore, many prefer to repair their favorite shoes on their own.

How to care for boots

Rubber products must be properly looked after. And then you do not have to resort to their frequent repair. After all, even the high quality guaranteed by the manufacturer does not always mean the safety of shoes.

Rubber boots must be properly cleaned. Best of all, they are washed with a solution of glycerin and water. At the same time, boots should be wiped with a soft cloth and often dried so that the fungus does not appear. Wet gumboots must not be dried with a hairdryer or battery. Shoes need to dry in natural conditions.

Tips before gluing boots

In order for the repair of boots to be successful, and the shoes have served a very long duty, you need to know the following:

1. Before repair, rubber shoes must be thoroughly cleaned, washed and dried.
2. The patch can be cut from a tire or old rubber boots.
3. It is better to carefully process the patch from the inside out with a sandpaper or a file to make the surface rough for better adhesion of the glue.
4. It is best to degrease the surface of the shoe with acetone and solvent.
5. Special glue should be chosen, on which it is necessarily indicated, for example, “shoe” or “rubber”.
6. Before repairing rubber boots, it is imperative to read the instructions from the adhesive manufacturer in order to do everything correctly.
7. It is best to smear the patch and the place of gluing with special glue several times, after waiting until the first layer dries a little.
8. When gluing the surface, you need to very strongly press each other or knock on the place of gluing with a hammer.
9. The patch on the boot can easily be masked with sandpaper.

4 ways to seal rubber boots

Method 1 You can seal the boots with special glue. It can be purchased in shops for hunters and fishers. But in order to get the right glue, you need to know what shoes are made of. The fact is that for EVA or polyurethane shoes you need different adhesives.

The seller can help to get the necessary glue, giving advice. Further, everything is simple - you need to sand and degrease part of the boot and stick a patch. If the shoes are made of porous material, then you can glue them without using a patch. The edges at the site of the cut simply need to be turned out, greased liberally with glue and pressed to each other.

Method 2 For this method, you need a regular bicycle repair kit. It contains patches on special protective films, sandpaper and, of course, glue. Sand the desired place on the shoe and degrease it well. Further, having previously removed the film from the bookmark, it is necessary to apply glue on it and press the patch to the gap. You can use shoes almost immediately, but it’s better to wait at least 12 hours. The only disadvantage of this method is the unaesthetic look of shoes after repair.

If the hole appeared not on the shaft, but on the sole, the bonding technology does not change. You just need to make the surface smooth and even, because usually the sole on such shoes is quite embossed. This is possible with a grinding machine. And only then stick a patch on this place.

But it is important to know that such a patch will not last long, especially if the sole of the boot will very often come in contact with a rough and hard surface. Therefore, such boots are best worn, for example, for fishing. Well, if the sole breaks again, the gluing procedure will need to be repeated.

Method 3 In order to stick on women's boots without using patches, etc., it is necessary to purchase adhesive sealant. You can do this in any store for car enthusiasts. First you need to degrease the place of gluing, and then grease the torn edges with glue and press against each other. If you do everything carefully, the boots will look like new.

Method 4 This method of repairing rubber shoes is also called the "hot" method. It is not complicated, but it requires certain skills and, most importantly, a vulcanizer. As a patch, use rubber pre-soaked in gasoline. It is placed on the hole in the boot and clamped with a vulcanizer. The device must be turned on for 20-30 minutes, then turned off and cool. Only after it cools down can you remove the press.

Do not despair if your favorite rubber boots suddenly torn. It is enough to make a little effort and the repaired boots will not be any different from the new shoes. You can use taped boots a day after the patch has been applied. But if there is no time to wait, then you can go to them in an hour.

Video: how to stick rubber boots on your own